IMPORTANT NOTICE - STORE IS UNDER CONSTRUCTION. DURING THIS TIME TRANSACTIONS WILL NOT BE PROCESSED!!
RAILINGS

Sentry Handrails are perfect for all indoor and outdoor applications ranging from traditional to commercial safety railings. Manufactured by JHA Associates Ltd. of the finest aluminum alloy, Sentry Handrails offers a wide range of styles and provides a super-strong, low maintenance system. All of our handrail products meet international safety requirements.

    


DURABILITY & MAINTENANCE

Sentry Handrails are made from the highest quality extruded aluminum alloy and stainless steel hardware available and manufactured with the strictest attention to detail, performance and durability.

JHA is committed to providing a wide spectrum of advanced high quality products that keep pace with the fast moving construction industry. Our products provide architects, designers, building contractors, developers and facility managers the competitive edge through effective and attractive solutions in architectural finishes.


STYLES




 

STANDARD POWER COAT COLOUR OPTIONS - R03

Gloss - White, Black, Dark Bronze.
*Custom colors avaliable in wet spray applications.


TECHNICAL SPECIFICATIONS - R03

Rails: R03
1.6” x 2.5” extruded aluminum top rail with snap plate
1” x 1.8” extruded aluminum intermediate rails (with or without snap plates).

Post:
2” x 2” aluminum SHS post.

Pickets:
1” aluminum SHS pickets.


INSTALLATION

1.0 EXAMINATION & PREPARATION

1.1 Verify that field conditions are acceptable and are ready to receive work.

1.2 Make provision for erection/loads with temporary bracing if necessary.


2.0 INSTALLATION

2.1 Install items plumb and level, accurately fitted, free from distortion or defects.

2.2 Fit exposed connections accurately together to form tight, hairline joints, except as required for expansion.

2.3 Cutting, Fitting & Placement: perform cutting, drilling and fitting required for installation of handrails and railings. Set handrails & railings accurately in location, alignment and elevation, measured from established lines and levels and free from rack.
   a) Set posts plumb with a tolerance of 1/16” to 12”.
   b) Align rails so that variations from level for horizontal members do not exceed 1/32” in 12”.

2.4 Corrosion Protection: Cast concealed surfaces of aluminium that will come into contact with grout, concrete, masonry, wood, or dissimilar metals with a heavy coat of paint or epoxy.


3.0 STORAGE

3.1 Product to be stored in clean, dry location, away from uncured concrete masonry, stucco or paint. Protect against damage of any kind to ensure a complete and satisfactory installation.


4.0 ANCHORING POSTS

4.1 Anchor posts in concrete by means of pre-set sleeves into concrete. After posts have been inserted into sleeves, fill space between post and sleeve solid with the following anchoring material, mixed and placed to comply with anchoring material manufacturer’s directions.

4.2 Anchor posts in concrete by core drilling holes not less than 3” deep and 1” greater than outside diameter of post. Clean holes of all loose material, insert posts, and fill space between post and concrete with the following anchoring material, mixed and placed to comply with anchoring material manufacturer’s directions.

4.3 Leave anchoring material down approximately ½” to allow for final topping with a waterproof material matching the surrounding areas. Whenever possible fill hole with waterproof topping slightly higher than the adjacent surfaces and taper and taper-away from the post.


5.0 GROUT & ANCHORING CEMENT

5.1 Non-Shrink, Non-Metallic Grout: Premixed, factory packaged, non-staining, non-corrosive, non-gaseous grout. Provide grout specifically recommended by manufacturer for interior and exterior applications of type specified in this section.

5.2 Erosion-Resistant Anchoring Cement: Factory pre-packaged, non-shrink, non-staining, high strength formulation for fixing with water at installation site to create pourable anchoring, patching and grouting compound. Provide formulation that is resistant to erosion from water exposure or provide a sealer or waterproof coating recommended for use by manufacturer to be applied by the installer or other qualified contractor or subcontractor.


6.0 CLEANING, PROTECTION AND TOUCH-UP PAINTING

6.1 Painted aluminum surfaces shall be cleaned with plain water containing a mild detergent. No abrasive agents or harsh chemicals are to be used.

6.2 Touch-up with paint same colour as finish as directed by Architect prior to acceptance.

6.3 All railings require periodic maintenance. All railing surfaces require periodic washing especially those subject to ocean salt air.


COMPONENTS




CONNECTIONS




CUSTOM FENCING

JHA Associated Limited can manufacture custom-designed handrails for any commercial, residential or hotel property. Fax or e-mail in your design to the Customer Service Department and an estimate will be provided for the job.





           << BACK TO PRODUCTS